There are more and more various mobile devices on people's bodies, and the demand for charging is also growing. It is very important to purchase a set of efficient and safe charger equipment. Today, I was lucky to test the three piece desktop charger, car charger and mobile power supply of ORUCO. Thanks for Lei Feng's trial and the opportunity provided by ORECO. The brand of ORECO has not been introduced much. The desktop charger in the fast charging package is a five port charger that supports the QC2.0 protocol. The car charger supports QC3.0, and the mobile power supply also supports the 2A fast charging.

I won't say much. Let's have a look at the specific charging effect.

*The mobile phones in this test are Xiaomi 5 (QC3.0) and vivo Xplay5 (QC2.0)

The outer packaging of the three products is not uniform. The desktop charger and mobile power supply are all packed in white paper boxes, while the car charger uses a kraft paper box+jacket cover design. Let's look at them one by one.

Q1 mobile power supply

Open the box and the mobile power supply is directly available. It can be seen that the package indicates that 5V/9V/12V fast charging is supported. In addition to the mobile power supply, the accessory has a short Micro USB cable and a manual warranty card.

The shell of Q1 is made of frosted aluminum alloy, which feels good and is not easy to leave fingerprints and sweat. The frame is chamfered to prevent hand cutting, and the process is relatively fine. The top is the power key, indicator light, input and output interface. Tear off the protective film, the mirror effect is very good.

The bottom is marked with specification parameters, and the total power is 10400mAh. It can output 5V~2.1A, 9V~1.8A, 12V~1.35A three gear voltage and current, and the input is 5V~2.1A

The size and thickness of Q1 is similar to that of conventional mobile power supply, which is convenient to hold in hand. The equipped short charging line is very convenient for charging mobile phones when going out. The original charging line of mobile phones is often more than one meter long, which is not easy to carry and inconvenient to charge, so you can take this short line when going out.

Let's see the charging effect. When charging Xiaomi 5 and vivo Xplay5, the voltage can barely reach 9v, which is basically up to the standard. However, since QC3.0 is not supported, the charging speed of Xiaomi5 will be slower.

When charging Q1, the voltage can reach 9v, which is somewhat different from the "input 5V~2.1A" marked in the parameters. Although the actual high voltage charging is fast, I still hope that the manufacturer of ORECO can pay attention to these details.

QC2.0 Desktop Charging

This desktop charger supports the QC2.0 protocol and has five ports, which can basically meet the charging needs of all mobile devices on the desktop.

The charger is made of frosted plastic, and the color of black and gray will not be conspicuous on the table. One of the five charging ports is a green QC2.0 port, and the other four are ordinary 5V fast charging ports. The back is marked with parameters, and the total output is 5V~8A.

The other end of the charger is the power interface.

Actual charging effect

The voltage of the QC2.0 port can reach the nominal 9v (the current in the picture is low because the phone is full, and the QC protocol will reduce the current)

The common port is 5.1V~1.41A, which also meets the standard.

As a five port desktop charger, it is necessary to test whether it can provide stable voltage when several devices are mounted.

In addition to charging three mobile phones at the same time, I also hang a 2A load resistor. It can be seen that the QC2.0 port of the charger can provide 9V voltage at this time, with a total power of about 35W. In general, this charger is very powerful.

QC3.0 Vehicle Charging

The packaging of this car charger is different from the other two products. It uses kraft paper. The car charger supports QC3.0, which provides one gear per 0.2V from 3.6V to 12V.

The polished shell of the car charger is very beautiful, and black is also suitable for putting in the car. The charger provides three ports, one orange port is QC3.0 port, and the other two are 5V ports. The overall process is very exquisite, and the bottom metal contact is also engraved with a ring pattern.

The three ports on the back of the car charger are marked with QC3.0, 5v~2.4A and 5V~1A respectively.

Use QC3.0 port to charge Xiaomi 5. The current and voltage are 6.47V~2.44A, which fully meet the charging standard of QC3.0. When charging a vivo that only supports QC2.0, the voltage is changed to 9V, which is more intelligent.

When a 2A load resistor is attached, the QC3.0 port can still provide a voltage of more than 9V. However, in this case, the voltage of the third port is less than 5v, and cannot charge another mobile phone. So although the car charger has three ports, it can only charge two mobile phones that support fast charging. However, if it is a 5v~1a device like iPhone, there is no pressure on the three ports.

summary

I am very satisfied with these three fast charging products. Not only is the charging efficiency very high, but also they all meet the standard. The appearance and quality of the products are also very exquisite. The desktop charger has five ports, which can catch all the devices that need to be charged on the desktop, but it would be better if it could support QC3.0. Similarly, it is hoped that mobile power can support QC3.0, which can not only cover QC2.0 devices, but also provide faster charging speed for more users with new QC3.0 mobile phones.

And as a package, it should be at least the same specification, so it is recommended that all three products be set to support QC3.0 fast charging.

Finally, I would like to thank Lei Feng for his trial and Orico's products.