The ultra-thin wireless charger is full of expectations for a digital product enthusiast~ After receiving the test supplies of the VH "and" wireless charger Lei Feng, take a closer look from inside to outside.

The length and width of the product packaging box are 25cm * 13.5cm, and the overall thickness is 1.3cm. There are two lights inside the open carton The round design of the size of the disc is that one side is a disc shaped charging base like a coffee cup disc, and the other side is a flat cable with a charging socket. The box cover can be clearly seen at this time The box bottom and the middle fixed storage position are composed of four layers of paper shells with a thickness of about 0.3cm. The box cover and bottom are hard enough and lightweight. The overall gray packaging is environmentally friendly, simple and low-key, but at the same time, it is very Texture, like a thin Notebook, is my favorite style, which meets the basic portability for people who often travel.

This wireless charging requires a special charging sticker attached to the back of the phone. I chose the Apple phone special model. The charging sticker is placed in a small box separately, regardless of the external package or the charging sticker However, it is low-key gray. The whole paste is like an enlarged version of a band aid with a long tail. The thin, soft piece is only about 0.1cm long. The feel of suede is good. Press the illustration on the small box of the charging sticker to insert the charging sticker The metal head of the mobile phone is inserted into the charging port of the mobile phone, and the other end is peeled and glued to the back of the mobile phone like a sticker, and the mobile phone is placed on the charging tray.

Can't wait to start the operation. Insert the metal head of the charging sticker into the charging port. At this time, it is found that the connected cable is completely bare without any protection, which makes people feel vaguely worried about the wear resistance（ This point is not shown in the table below), and then tear the charging patch completely, exposing the metal contact near the end of the charging head, which is really crude. I doubt the repeated adhesion ability of the patch, and worry about such problems as If the fruit is stuck on the phone for a long time, whether it will leave glue marks on the phone. The charging sticker is very thin on the phone, but it cannot be exposed on the phone case. On the one hand, the suede is not resistant to dirt, on the other hand, it is very easy to look like me We have applied Band Aids, and after a few rubs, the edges fall off everywhere. Does this design mean that we must use the mobile phone shell? My existing mobile phone has a soft thin glue The mobile phone shell can be easily put on after the charging sticker is glued, which does not affect the fit between the shell and the mobile phone, but still has a prominent feel. Required if hard and inelastic housing is used Pay attention to the obstruction of the metal plug at the lower back of the charging sticker and the fitting between the rear cover and the mobile phone.

Then take out the charging seat. The charging cable has a plastic shell, and it is not confirmed whether it is glue. The handle of the cable is even and smooth. The charging seat is coffee colored imitation leather, and it is placed with the table and tea set without any incongruity On the table, it looks like a coffee coaster. I have the impulse to put the coffee cup on several times.

Get ready to charge immediately, and then find that you can only plug it into the computer through USB or use Apple's charging plug. That is to say, if you are on a business trip, you still need to bring an additional plug, er~also It should be used in fixed places such as home and office as far as possible.

Put the phone on the middle of the disc and simply put it on the fast docking. Even if I try to adjust it slightly, the connection is still not affected. The overall charging is smooth, and the charging speed and the normal data line direct charging speed are not clear Significant difference, basic conversion ability is good. Later, I tried to fix the charging sticker directly on the back of the phone through the phone case without tearing the adhesive, and the charging speed was still good with my phone case, Basically maintain the charging speed of 1% in 1 minute. Some testers reported that the heat dissipation of the charging tray is poor, which may lead to more than 40 degrees in the tray. Since it is cold and there is no heating in the south The heat dissipation problem is basically insensitive.

During the test, a friend came to visit and was very interested in this new gadget. They changed to their own mobile phones to experience it. The poor charging stickers were pulled out and inserted on different mobile phones. The fragile bare running cables I was extremely anxious when I was pulled. I reminded my friends to carefully pull out the metal plug with their fingernails, but later found that there might be some damage to the inside of the cable. Sometimes the phone is left on the charging tray It will break for no reason, adjust your posture and connect again. In addition, after a few days, the cable has obvious creases. When you put the phone cover on, it is still squeezed and rubbed naked, and the life is really long It's hard to last.  

A few days later, I began to think whether I would design such a product as a designer? Are I willing to pay for such a tangled product? Its advantage is that the charging sticker is really thin, but the charging cable is bare and the design of the charging sticker is suede. I don't know why! For example, the charging sticker cannot be used, which is easier to clean, wear-resistant and light Other thin materials?

Its advantage is that if there are multiple mobile phone users in a public place such as a home or an office colleague or coffee shop, even different models can share the charging tray, without requiring different data Cable and charging cable, but the premise is that each user is either a rechargeable mobile phone or equipped with a charging sticker! The same model can also be shared (taking out trouble and cable damage are not considered temporarily Risks), different phones with different sockets need to buy different special funds. If the price is very cheap, I will accept it. I will also accept the problem that the cable is exposed and not wear-resistant. If it breaks, I can buy it at any time! It also has the advantage that the design of the round coaster charging tray is very textured, but the flat and long charging cable at the back is still very impressive! It greatly reduces the beauty of the disc. Its advantage is that the environment-friendly thin paper shell is easy to carry, but the paper is still paper! If you leave it at home carelessly, it will be stained. If you go out, you need to bring an extra charging plug, If it is not easier to add a charging plug and a data cable, what is the significance of taking a disk?

All of the above "and" didn't meet my expectations, which made me lose enthusiasm step by step and completely lost the willingness to buy or recommend this product to friends. Wireless charging is a relatively mature technology It is a challenging proposition to let old technology breathe new life. For example, how to make all models of mobile phones share wireless charging without special design. I don't know the answer, but I know Without fundamental and comprehensive improvement of customer experience and accurate positioning of products, it is difficult to attract customers to change their existing equipment and usage habits at the lowest price, and there is no market space , packed with innovative gimmicks, produced and sold in the form of fashion crowdfunding, will eventually be a flash in the pan, become a digital product enthusiast who dares to try new products, and become a dusty sundry in the corner, moving quickly Landfill.